GETTING STARTED WITH PLUMBER'S ESSENTIALS FOR BATHTUB INSTALLATION

Getting Started with Plumber's Essentials for Bathtub Installation

Getting Started with Plumber's Essentials for Bathtub Installation

Blog Article

Call

Just about every person has got his or her own theory about How to Install a Bathtub Yourself.


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a bathtub isn't specifically rocket science, but it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is additionally a moderately hard project. If the old bathtub is readily obtainable, the project can relocate quickly; if you need to open up a wall to remove the old bathtub and position the brand-new bath tub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work as well as are comfortable trying it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This post will help you install a brand-new tub in your restroom if you have currently purchased a new bathtub as well as do not require to change the setup of your previous water system pipes.
Your devices and product checklist should make up the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is detach the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the restricted accessibility that is usually the instance.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the staying water that will come from the pipelines. When the supply pipes have actually been removed, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from turning throughout this procedure. When the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned up of any kind of old securing compound.
    Prior to proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

    Suitable New Taps


    If the tails of the new faucets are plastic, after that you will require a plastic adapter to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
    Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in area between the tap and the sink. Protect the tap in position with the producer offered backnut. Once the faucet is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal faucet ports. The former type ought to be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Mounting the Bath tub


    Using the two wood boards under its feet, position the bath tub in the required position. The wooden boards are handy in evenly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
    The next goal is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and also changing the feet on the tub up until the spirit level reads degree.
    To install taps, fit all-time low of the outermost flexible tap port to the ideal supply pipeline by making a compression join; then do the exact same for the various other tap.
    Turn on the water and also check all joints and brand-new pipework for leaks and also tighten them if necessary. Load the bath tub as well as additionally check the overflow electrical outlet as well as the normal outlet for leaks.
    Finally, repair the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been made use of a minimum of when as this will certainly resolve it right into its last placement.

    Preparing for the Installation


    First of all, the supporting framework supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a supporting plate under the faucets device to avoid strain on the bathtub.
    Fit the adaptable faucet connectors to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washers.
    Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath must currently prepare to be fitted in its final setting.

    Tiling Around the Bath tub


    In the location where the bathroom meets the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall between the bath and also the tiling, leading to complications with dampness and also feasible leaks to the ceiling below.
    You can choose from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can break rather early if you do not think about this activity prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the tiles using water-resistant or water resistant sticky as well as cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    I was shown that article on A Step-by-Step Guide to Installing a Bathtub from a good friend on another web blog. Those who enjoyed reading our blog posting please be sure to pass it around. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Contact for quality!

    Report this page